$117.49 Buy It Now or Best Offer
free,30-Day Returns
Seller Store
() %,
Location: Ontario, California, United States
Ships to: US,
Item: 313389170891
eBay 1.Fit For Jeep Wrangler 60 4.0L 2001 Jeep Wrangler 65th 4.0L 2006 Jeep Wrangler Base 2.5L 1997 Jeep Wrangler Rubicon 4.0L 2003-2006 Jeep Wrangler SE 2.4L 2003-2006 Jeep Wrangler SE 2.5L 1997-2002 Jeep Wrangler SE 4.0L 2006 Jeep Wrangler Sahara 4.0L 1997-2004 Jeep Wrangler Sport 4.0L 1997-2006 Jeep Wrangler Unlimited 4.0L 2004-2006 Jeep Wrangler X 4.0L 2002-2006 2.Package Includes: 1x Part# Tie Rod Drag Link Outer Connecting Passenger Side – DS1430 1x Part# Front Driver Side Outer Tie Rod End – ES3094 1x Part# Front Passenger Side Inner Tie Rod End – ES3095 1x Part# Front Outer Tie Rod End Driver Side – ES3096 Fits 1997-2006 Jeep Wrangler Front Tierod Track Bar Sway Bar Link Ball Joint Kit 1.Fit For Jeep Wrangler 60 4.0L 2001 Jeep Wrangler 65th 4.0L 2006 Jeep Wrangler Base 2.5L 1997 Jeep Wrangler Rubicon 4.0L 2003-2006 Jeep Wrangler SE 2.4L 2003-2006 Jeep Wrangler SE 2.5L 1997-2002 Jeep Wrangler SE 4.0L 2006 Jeep Wrangler Sahara 4.0L 1997-2004 Jeep Wrangler Sport 4.0L 1997-2006 Jeep Wrangler Unlimited 4.0L 2004-2006 Jeep Wrangler X 4.0L 2002-2006 2.Package Includes: 1x Part# Tie Rod Drag Link Outer Connecting Passenger Side – DS1430 1x Part# Front Driver Side Outer Tie Rod End – ES3094 1x Part# Front Passenger Side Inner Tie Rod End – ES3095 1x Part# Front Outer Tie Rod End Driver Side – ES3096 1x Part# Steering Tie Rod End Adjusting Sleeve – DS1326 1x Part# Front Passenger Side Tie Rod Adjusting Sleeve – ES2079 1x Part# Front Suspension Track Bar – DS1235 2x Part# Front Stabilizer Sway Bar End Links Driver & Passenger Side – K3197 2x Part# Front Upper Ball Joints – K3134 2x Part# Front Lower Ball Joints – K3161 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Lower Type : Sway Bar Link Universal Fitment : No Custom Bundle : Yes Interchange Part Number : K3134T K3161T ES3096L ES2079S ES3094L ES3095R DS1235 OE/OEM Part Number : Suspension Steering Tie Rod Ends Linkages Assembly,Ball Joints Bundle Description : Ball Joint,Tie Rod End (Adjusting Sleeve),Track Bar,Sway Bar Superseded Part Number : Front Driver and Passenger Side Replacement Manufacturer Warranty : 10 Year Brand : topcn-autoparts UPC : Does Not Apply Manufacturer Part Number : TA82831106P Adjustable : Yes Greasable or Sealed : Greasable Kit Included : 13 Pieces Surface Finish : Premium Quality Cross Part Number : K3197 DS1430 DS1326S Cross Reference Part Number : 1998 1999 2000 2001 2002 2003 2004 2005 Fitment : For 1997-2006 JEEP WRANGLER Cross Reference Part Number : 1998 1999 2000 2001 2002 2003 2004 2005 Fitment : For 1997-2006 JEEP WRANGLER Features : Greasable Finish : Coated Material : Alloy Steel Mounting Style : Bolt-On Cotter Pin Hole : Yes Discount Targeted Discounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means Topcn-autoparts won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Topcn-autoparts has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Shipping WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Warranty Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).Topcn-autoparts carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).Topcn-autoparts promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise Topcn-autoparts has the right to refuse any replacement requests. (5).Topcn-autoparts promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise Topcn-autoparts has the right to refuse any replacement requests. (6).Topcn-autoparts carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).Topcn-autoparts has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. Return (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Best Sales 2 for Dodge Challenger 2008 2009 2010 2011 2012 2013 2014 Keyless Remote Key Fob USD 22.88 2x Front Hood Gas Lift Supports Struts Shocks Springs For Dodge Ram 02-10 4364 USD 18.69 2 X Front/Rear Wheel Hub Bearing For Buick LaCrosse Century Chevy Impala Venture USD 63.53 2x Front Hood Lift Supports Shocks Struts For Dodge Ram 1500 2500 3500 4500 5500 USD 14.79 Pair Front Wheel Bearings For Chevrolet Impala Buick Pontiac Grand Prix Montana USD 62.35 Newly Listed Bugflector Dark Smoke Hood Shield For 1995-2000 Toyota Tacoma USD 69.49 251A Power Steering Rack Gear For Mazda B2500 1999-2001 Ford Ranger 1998-2000 USD 260.99 Rack 280 Steering Rack & Pinion Assembly For Dodge Ram 1500 2002 – 2005 4X4 USD 245.00 Drive Shaft Bearing For 2001-2006 Santa Fe Gls Sport Utility 4-Door 2.7L 3.5L USD 25.58 Brand Driveshaft Propshaft 2211Mm For Mercedes Viano Vito Bus W639 6394103206 USD 417.78 Terms & Contact Shipping Policy Payment Policy Return Policy FAQ About Us Fits 1997-2006 Jeep Wrangler Front Tierod Track Bar Sway Bar Link Ball Joint Kit 1.Fit For Jeep Wrangler 60 4.0L 2001 Jeep Wrangler 65th 4.0L 2006 Jeep Wrangler Base 2.5L 1997 Jeep Wrangler Rubicon 4.0L 2003-2006 Jeep Wrangler SE 2.4L 2003-2006 Jeep Wrangler SE 2.5L 1997-2002 Jeep Wrangler SE 4.0L 2006 Jeep Wrangler Sahara 4.0L 1997-2004 Jeep Wrangler Sport 4.0L 1997-2006 Jeep Wrangler Unlimited 4.0L 2004-2006 Jeep Wrangler X 4.0L 2002-2006 2.Package Includes: 1x Part# Tie Rod Drag Link Outer Connecting Passenger Side – DS1430 1x Part# Front Driver Side Outer Tie Rod End – ES3094 1x Part# Front Passenger Side Inner Tie Rod End – ES3095 1x Part# Front Outer Tie Rod End Driver Side – ES3096 1x Part# Steering Tie Rod End Adjusting Sleeve – DS1326 1x Part# Front Passenger Side Tie Rod Adjusting Sleeve – ES2079 1x Part# Front Suspension Track Bar – DS1235 2x Part# Front Stabilizer Sway Bar End Links Driver & Passenger Side – K3197 2x Part# Front Upper Ball Joints – K3134 2x Part# Front Lower Ball Joints – K3161 Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Lower Type : Sway Bar Link Universal Fitment : No Custom Bundle : Yes Interchange Part Number : K3134T K3161T ES3096L ES2079S ES3094L ES3095R DS1235 OE/OEM Part Number : Suspension Steering Tie Rod Ends Linkages Assembly,Ball Joints Bundle Description : Ball Joint,Tie Rod End (Adjusting Sleeve),Track Bar,Sway Bar Superseded Part Number : Front Driver and Passenger Side Replacement Manufacturer Warranty : 10 Year Brand : topcn-autoparts UPC : Does Not Apply Manufacturer Part Number : TA82831106P Adjustable : Yes Greasable or Sealed : Greasable Kit Included : 13 Pieces Surface Finish : Premium Quality Cross Part Number : K3197 DS1430 DS1326S Cross Reference Part Number : 1998 1999 2000 2001 2002 2003 2004 2005 Fitment : For 1997-2006 JEEP WRANGLER Cross Reference Part Number : 1998 1999 2000 2001 2002 2003 2004 2005 Fitment : For 1997-2006 JEEP WRANGLER Features : Greasable Finish : Coated Material : Alloy Steel Mounting Style : Bolt-On Cotter Pin Hole : Yes DiscountShippingWarrantyReturnFeedback Targeted Discounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means Topcn-autoparts won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Topcn-autoparts has the final power of interpretation of all the above Targeted Discount Terms and Procedures. WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).Topcn-autoparts carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).Topcn-autoparts promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise Topcn-autoparts has the right to refuse any replacement requests. (5).Topcn-autoparts promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise Topcn-autoparts has the right to refuse any replacement requests. (6).Topcn-autoparts carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).Topcn-autoparts has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Copyright of Topcn-autoparts. All rights reserved.
Frequently Asked Questions About Fits 1997-2006 Jeep Wrangler Front Tierod Track Bar Sway Bar Link Ball Joint Kit in My Website
ar.abumaizar.com is the best online shopping platform where you can buy Fits 1997-2006 Jeep Wrangler Front Tierod Track Bar Sway Bar Link Ball Joint Kit from renowned brand(s). ar.abumaizar.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
What are the best-selling Fits 1997-2006 Jeep Wrangler Front Tierod Track Bar Sway Bar Link Ball Joint Kit on ar.abumaizar.com?
ar.abumaizar.com helps you to shop online and delivers Champion to your doorstep. The best-selling Champion on ar.abumaizar.com are: Champion Long Sleeve T Shirt Mens SIZE L (L) f75dbc2812b8f9bd9dee305945c520e1 Men’s PumpDay Champion Long Sleeve Shirt Champion Shirt Adult Small Gray Cotton Casual Outdoors Preppy Spell Out Mens Champion Knit Shirt Men’s Size Large Black Short Sleeve Crew Neck Cotton Champion Shirt Men’s Large Red Cotton Layered Look Active/Casual Champion Sportswear T-Shirt Blue Logo Spellout Short Sleeve 2XL Champion Short Sleeve T Shirt Multi Blue Print Size XXL Extra Extra Large James Hunt Sex Breakfast Of Champions / Formula 1 / %100 Premium Cotton Champion Mens Black Graphic T Shirt – Champion – Size Medium Vintage Y2K kelly green Champion tshirt short slv sz M active preppy Champion Shirt Adult 2XL XXL Authentic Athletic Red Signature Logo Mens Champion Men’s Long Sleeve Collared Pullover Lightweight Gray Size S Champion T Shirt Men’s XL Red Cotton Tee Small Logo USA Athleisure Alabama Champion Football Fan Cardinal T-shirt Hate Us Cause They Ain’t Us S-5XL Champion Doubly Dry Mens Black Graphic Polyester T Shirt Size L Russia 2018 France Champion T Shirt Men’s Large Short Sleeve Blue 100% Cotton Champion T-shirt men’s short sleeve white print logo Size：S Champion Gray T-Shirt Notorious B.I.G. Size Large Champion Shirt Mens SMALL white Short Sleeve Shirt Cotton logo t-shirt Size S NBA Finals Champions Golden State Warriors Wool Blend Banner 14″×21.5″ Champion Kids’ Girls’ Rally Pink Lace-Up Sneaker Tennis Shoes 1-4 Medium CF MARTIN & COMPANY Owners Club T-Shirt Guitar Acoustic Size LG New Champion Cardigan snap Up Sweatshirt Jacket Men’s Med (CL-108) Champion Men’s Shirt Size M Medium Lined Mesh T-Shirt Authentic Athleticwear N Y Yankees 2009 World Series Champions White T-Shirt Players names NEW Ch. Size Champion Athletics Basketball League Gray XL T-Shirt Champion Shirt Mens Medium Red Casual Short Sleeve Tee Shirt Crew Neck Adults Rocky II Win Rocky Long Sleeve Graphic T-shirt – Classic Stallone Tee MGM225 Champion Shirt Mens Large Adult Short Sleeve Crew Neck Lightweight Outdoors Champion Athletic T-Shirt Mens 2XL XXL Navy Blue Short Sleeve Crew Neck H79 Champion Shirt Mens Short Sleeve 100% Cotton Athletic Large Logo Burgundy M Congrats Minnesota Lynx team 2024 WNBA Commissioner’s Cup Champions t-shirt Champion Black Spellout T-shirt Large EUC Champion T Shirt Men’s Size M, White with Navy & Red Logo-Front & Sleeve Champion T-shirt M & L Long Sleeve Balboa Blue 100% Cotton Athleticwear Champion C Lock CPS10525M Black Men’s Casual Sneaker Boots Shoes Men’s 100% Authentic Champion Long Sleeve T-shirt Size Large Color Grey Boston Celtics Sticker Champions NBA logo STICKERS Champion Mens Blue Graphic Logo T Shirt Size Small Champion 100 Year Anniversary Embroidered Tee Shirt Size XS Extra Small Champion Authentic Athleticwear Size 2XL XXL Blue Short Sleeve T Shirt Champion T Shirt Men’s Large Grey Cotton Tee Big Logo USA Athleisure CHAMPION Mens Long Sleeve Crew Neck T Shirt Turquoise Cotton SZ LARGE Champion Black Im That Good Short Sleeve T-Shirt Mens XLARGE champion t shirt medium Blue /Heavier Cotton FREE SHIPPING HOT 2024 – L0s Angeles D0dgers 2024 World Series Champions Unisex Vintage 90s Chicago Bears Cropped Mesh Jersey Manchester United Nike Tshirt mens medium black 2006/2007 champions soccer Harlem Heat Wrestling Tag Team Champions Fan Hoodie DENVER NUGGETS 2023 FIRST TIME NBA CHAMPIONS EXCLUSIVE LIMITED EDITION 500 PIN Champion Men’s Short Sleeve Gray Spell Out Logo T-Shirt Small NWT Champion Men’s Athletics Classic Jersey Tee Record Logo Medium Gray Burgundy NWT Champion Tee Shirt For Men 2XL Baby Blue Champion Green Khaki Large Cotton T Shirt T16 Champion Full Chest Script Logo Short Sleeve T-Shirt Orange Mens Size 1XL Champion Blue Shirt Mens Size Small Short Sleeves 100% Cotton Crossfit Mayhem Freedom Affiliate Cup Champions-Men’s 2XL 2020 NBA Finals Champions Die-Cut Magnet CHICAGO BLACKHAWKS New Mens 2013 Stanley Cup Champions Shirt Black TEAM ROSTER NWT! Rappahannock Commnuity College Nursing Champion T-Shirt Men’s Size Medium Mike Myers Tshirt World Champion 1978 Power Walker Short Sleeve Crew Neck Top Champion Men’s Tshirt XL Michael Schumacher F1 World Champion 7-times Formula 1 Vintage Ferrari Hat Cap NEW! C9 by Champion X-Large Active Wear Aqua Golf Polo Shirt Delta Mens Phillies 2008 National League Champions Graphic T-Shirt Red Tee XL USA Flag City of Chicago KEE Firearms & Training Hoodie CHAMPION Men’s LARGE Champion Beefy Spellout Graphic Tee Shirt Mens Large Green Short Sleeve Crewneck Champion Shirt Men’s XL Blue Lightweight Athletic Casual Outdoors Coco Gauff US Open Champion Tennis Fan T Shirt Champion Shirt Mens Extra Large Athletic Pride Script Tee Blue Short Sleeve Champion T Shirt Men’s Small Grey Long Sleeve Spell Out Cotton Tee Athleisure Champion T Shirt Men’s Medium Navy Blue Spell Out Cotton Tee Logo USA Athleisure Champion Men’s Long Sleeve Pullover Gray Logo Shirt Large Champion Men Crew Neck Short Sleeves T-Shirt Small Maroon Champion Shirt Mens S Small White Athleisure T Shirt Short Sleeve Spell Out Champion Authentic T-Shirt Blue Men’s Size XL Preowned Small Logo Fast Ship Champion Men’s Boxer Briefs 5-pack – MIXED COLORS (Select Size) BRAND NEW SEALED Hazelwoods 1990’s, 1993 Men’s Graphic T-Shirt, World Champion Grandpa, Black, XL Champion Star Shirt (Size Medium) Grey/blue Champion Bulldog University Graphic T Shirt Mens Small Short Sleeve Black Champion 2 Pack Womens Sports Bra with Removable Foam Cups Wire Free Racerback Two Cobalt Boats Screen Printed Champion T-Shirts 6.1 oz. Heavy Weight Champion Authentic Men’s Orange Cotton Short Sleeve Crew Neck T-Shirt Size S Champion Men’s Medium Dark Grey T-Shirt Short Sleeve Activewear Crew Neck Shirt Air Jordan Wings Logo Champion T-Shirt bulls MJ 23 UNISEX Los Angeles Dodgers 2024 World Series Champions Locker Room Parade T-Shirt Champion Powerblend Men’s Pullover Hoodies Chainstitch/Patch Logo GF89H GF88H Original Champion Men’s Classic Jersey Script Soft Cotton Long Sleeve T-Shirt Paris Olympics 2024 Champion Hoodie Champion Shirt Mens Medium Red Crew Neck Blank Short Sleeve Embroidered Logo Men’s Champion XL Extra Large Blue Short Sleeve Collared Button Up Casual Wear YOUTH SIZE CHAMPION RF MID CPS10219Y BLACK GREY SNEAKER SLIP ON Champion Women’s Short Sleeve T-Shirt Champion Mens Shirt Medium White Short Sleeve Crew Neck Pullover Logo Tee NEW LMT! Tennessee Volunteers Champions 2024 Print Team T-Shirt Champion Logo T-Shirt Adult Small Crew Neck Short Sleeve Pullover Classic Red BLUE/GREY CREWNECK KNIT SHIRT Champion Men’s Short-Sleeve Logo T-Shirt (Grey, Small S, ) Champion Shirt Adult Extra Large Black Outdoors Athletic Casual Preppy Mens Champion Authentic Athleticwear Men’s Charcoal Gray T-shirt Size XL Mens Pullover Fleece Hoodie
عيادات أبوميزر للأسنان © 2023. جميع الحقوق محفوظة